 |
|
|
 |
 |
 |
Click image for larger view
|
P/N: ETI0018-2110
Tactical Transit Case DC/AC Power Inverter
1500 VA, 1000
Watts
12 VDC In, 120 VAC Out
Technical Specifications
|
Tactical Briefcase and
Transit Case Inverters:
|
 |
|
| AC OUTPUT |
| Output
voltage: |
120 VAC
true sinewave
Optional 220 VAC |
| Output
rating: |
1500 VA,
1000
watts continuous |
| Output
voltage regulation: |
± 3.0%
static regulation of nominal
-10% to +4.0% dynamic |
| Overload
surge capacity: |
2000
watts surge for 5 seconds |
| Output protection: |
Overcurrent
protection |
| Harmonic
distortion: |
Less than 3.0% THD |
| Output
frequency: |
60 Hz ± 0.5% crystal
controlled
Optional 50 Hz |
| Operational
status |
Status LCD
display, load level,
input volts/amps
audible alarm |
| DC
INPUT |
| Input voltage
selection: |
Nominal 12
VDC |
| Input voltage
tolerance: |
10-16 VDC |
| Input control/protection: |
2-pole
Guarded DC Circuit Breaker,
Under/Over voltage,
Input Reverse Protection,
Low Voltage Disconnect (LVD) protecting source so
vehicle battery does not go below starting voltage |
| Input power
connection: |
Quick connect (1) NATO Slave female and
Quick connect
(1) Anderson Power Pole |
| Input power
cable: |
Uses standard NATO Slave male-male cable or
Optional
10' Anderson to NATO Slave male connector |
| DISTRIBUTION
PANEL |
| Output
circuits: |
Six outputs
standard |
| Output protection: |
GFCI,
Ground Fault Circuit Interrupter |
| Output
control: |
Optional panel switches or breakers
Optional remote interlock ON/OFF control |
| Output
receptacles: |
NEMA 5-15R straight
blade standard |
| Ground connection: |
Quick connect jack |
| MECHANICAL |
| Enclosure type: |
Mil Grade Transit Case,
water tight to -30 ft w/pressure relief valve, lockable |
Rotation Mold Case
Dimensions ( H x D x W ):
Unit weight:
Inverter Built into Case only
Cable only
Inverter with Cable together |
19 in
(483 mm) x 16.4 in (417 mm) x 20 in (508 mm)
48 lb. (22
kg)
15 lb. (7
kg)
63 lb. (39
kg)
|
Injection Mold Case w/Wheels and Retractable Handle (A1
suffix)
Dimensions ( H x D x W ):
Unit weight:
Inverter Built into Case only
Cable only
Inverter with Cable together |
10 in
(254 mm) x 20.5 in (520 mm) x 15.5 in (394 mm)
42 lb.
(18 kg)
15 lb.
(7 kg)
57 lb.
(25 kg)
|
| Audible
noise: |
<47 dBA @ 5
ft., ANSI "A" scale |
| Cooling
type: |
Positive pressure fan.
thermostatically controlled,
over temperature protection |
|
Air intake filter: |
Easy clean intake air
filter |
|
ENVIRONMENTAL |
| Storage
temperature: |
-40° to
160° F ambient (-40° to 71° C),
lower/higher optional |
| Operating
temperature: |
-22° to
140° F ambient (-30° to 60° C
)
lower/higher optional |
| Operating
humidity: |
0 to 95%
relative humidity,
non-condensing, higher optional |
| Storage
elevation: |
Up to 40,000
ft (12,192 m) |
| Operating
elevation: |
Up to 10,000
ft (3,048 m), higher optional |
| STANDARDS |
| United
States: |
Meets UL-1741
and 458 |
| Canada: |
Meets CSA 107.1 safety
requirements |
|
International: |
Meets
EN60950-1 safety
requirements |
Electromagnetic
Compliance (EMC): |
EMI/RFI
FCC Part 15, Class B,
EN55022:1997, EN61000-3-2:1998,
EN61000-3-3:1995, EN550204:2001,
e-Mark e13-022025, Others optional |
| OPTIONAL
ACCESSORIES |
| |
Input
Cables, Ground Cables w/ Clamp, Ground
Rod Kit, Power Distribution Units, Remote
Control/Monitor Panel |
|
This
page was last modified on: May 17, 2008
|
|
|
 |
|
|
Copyright © 2000-2008 Energy Technologies, Inc.- All Worldwide
Rights Reserved.
TacticalPower®, Tactical Fuel Cells®, Tactical Generator®, Tactical Inverter®, TacticalPowerPlant®, Tactical Solar® and Military Power®
are registered
trademarks of Energy Technologies, Inc.
TacticalBriefcase™, TacticalCables™, TacticalComputers™, and
TacticalECU™
are trademarks of Energy Technologies, Inc.
Send comments or questions
regarding this site to: webmaster@tacticalpower.com
|